1 ? fn7387 caution: these devices are sensitive to electrostatic discharge; follow proper ic handling procedures. 1-888-intersil or 321-724-7143 | intersil (and design) is a registered trademark of intersil americas inc. copyright ? intersil americas inc. 2003. all rights reserved. elantec is a registered trademark of elantec semiconductor, inc. all other trademarks mentioned are the property of their respective owners. preliminary el5160, el5161, el5260, el5261, el5360 low-power, 200mhz current feedback amplifiers the el5160, el5161, el5260, el5261, and el5360 are current feedback amplifiers with a bandwidth of 200mhz and operate from just 0.75ma supply current. this makes these amplifiers ideal for today?s high speed video and monitor applications. with the ability to run from a single supply voltage from 5v to 10v, these amplifiers are ideal for handheld, portable, or battery-powered equipment. the el5160 also incorporates an enable and disable function to reduce the supply current to 100a typical per amplifier. allowing the ce pin to float or applying a low logic level will enable the amplifier. all packages operate over the industrial temperature range of -40c to +85c. features 200mhz -3db bandwidth 0.75ma supply current 1700v/s slew rate single and dual supply operation, from 5v to 10v supply span fast enable/disable (el5160 only) available in sot-23 packages applications battery powered equipment handheld, portable devices video amplifiers cable drivers rgb amplifiers test equipment instrumentation current to voltage converters ordering information part number package tape & reel pkg. dwg. # el5160is 8-pin so - mdp0027 el5160is-t7 8-pin so 7? mdp0027 el5160is-t13 8-pin so 13? mdp0027 el5160iw-t7 6-pin sot23 7? mdp0038 el5160iw-t13 6-pin sot23 13? mdp0038 el5161iw-t7 5-pin sot23 7? mdp0038 el5161iw-t13 5-pin sot23 13? mdp0038 el5260iy (note) 8-pin msop - mdp0043 el5260iy-t7 8-pin msop 7? mdp0043 el5260iy-t13 8-pin msop 13? mdp0043 el5261is (note) 8-pin so - mdp0027 el5261is-t7 8-pin so 7? mdp0027 el5261is-t13 8-pin so 13? mdp0027 el5360is (note) 16-pin so - mdp0027 el5360is-t7 16-pin so 7? mdp0027 el5360is-t13 16-pin so 13? mdp0027 el5360iu (note) 16-pin qsop - mdp0040 el5360iu-t7 16-pin qsop 7? mdp0040 el5360iu-t13 16-pin qsop 13? mdp0040 note: duals and triples to be released october 2003 data sheet august 29, 2003
2 pinouts el5160 (8-pin so) top view el5260 (8-pin so, msop) top view el5161 (5-pin sot-23) top view el5160 (6-pin sot-23) top view el5360 (16-pin so, qsop) top view 1 2 3 4 8 7 6 5 - + nc in- in+ vs- ce vs+ out nc 1 2 3 4 8 7 6 5 - + - + out1 in- in+ vs+ in- out2 vs- in+ 1 2 3 5 4 - + out vs- in+ vs+ in- 1 2 3 6 4 5 - + out vs- in+ vs+ in- ce 1 2 3 4 16 15 14 13 5 6 7 12 11 10 8 9 - + - + - + ina+ cea vs- ceb inb+ nc cec inc+ ina- outa vs+ outb inb- nc outc inc- el5160, el5161, el5260, el5261, el5360
3 absolute maximum ratings (t a = 25c) supply voltage between v s + and v s - . . . . . . . . . . . . . . . . . . . . . 11v maximum continuous output current . . . . . . . . . . . . . . . . . . . 50ma operating junction temperature . . . . . . . . . . . . . . . . . . . . . . . 125c pin voltages . . . . . . . . . . . . . . . . . . . . . . . . v s - - 0.5v to v s + + 0.5v power dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . see curves storage temperature . . . . . . . . . . . . . . . . . . . . . . . . -65c to +150c operating temperature . . . . . . . . . . . . . . . . . . . . . . . -40c to +85c caution: stresses above those listed in ?absolute maximum ratings? may cause permanent damage to the device. this is a stress o nly rating and operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. important note: all parameters having min/max specifications are guaranteed. typical values are for information purposes only. u nless otherwise noted, all tests are at the specified temperature and are pulsed tests, therefore: t j = t c = t a electrical specifications v s + = +5v, v s - = -5v, r f = 750 ? for a v = 1, r f = 400 ? for a v = 2, r l = 150 ? , v enable = v s + - 1v, t a = 25c, unless otherwise specified. parameter description conditions min typ max unit ac performance bw -3db bandwidth a v = +1, r l = 500 ? 200 mhz a v = +2, r l = 150 ? 125 mhz bw1 0.1db bandwidth r l = 100 ? 10 mhz sr slew rate v o = -2.5v to +2.5v, a v = +2, r f = r g = 1k ? 1000 1700 2500 v/s t s 0.1% settling time v out = -2.5v to +2.5v, a v = +2 35 ns e n input voltage noise 4nv/ hz i n - in- input current noise 7pa/ hz i n + in+ input current noise 8pa/ hz hd2 5mhz, 2.5v p-p -74 dbc hd3 5mhz, 2.5v p-p -50 dbc ip3 100 ? 500 ? dg differential gain error (note 1) a v = +2 0.1 % dp differential phase error (note 1) a v = +2 0.1 dc performance v os offset voltage -5 0 5 mv t c v os input offset voltage temperature coefficient measured from t min to t max 6v/c r ol + transimpedance 800 2000 k ? r ol - transimpedance 800 2000 k ? input characteristics cmir common mode input range 3 3.3 v cmrr common mode rejection ratio 50 62 75 db -icmr - input current common mode rejection -1 0 1 a/v +i in + input current -4 0.6 4 a -i in - input current -4 0.6 4 a r in input resistance 2715k ? c in input capacitance 1pf el5160, el5161, el5260, el5261, el5360
4 all intersil u.s. products are manufactured, asse mbled and tested utilizing iso9000 quality systems. intersil corporation?s quality certifications can be viewed at www.intersil.com/design/quality intersil products are sold by description only. intersil corporation reserves the right to make changes in circuit design, soft ware and/or specifications at any time without notice. accordingly, the reader is cautioned to verify that data sheets are current before placing orders. information furnishe d by intersil is believed to be accurate and reliable. however, no responsibility is assumed by intersil or its subsidiaries for its use; nor for any infringements of paten ts or other rights of third parties which may result from its use. no license is granted by implication or otherwise under any patent or patent rights of intersil or its subsidiari es. for information regarding intersil corporation and its products, see www.intersil.com output characteristics v o output voltage swing r l = 150 ? to gnd 3.1 3.4 3.8 v r l = 1k ? to gnd 3.8 4.0 4.2 v i out output current r l = 10 ? to gnd 40 70 110 ma supply i son supply current - enabled no load, v in = 0v 0.6 0.75 0.85 ma i soff + supply current - disabled -2 1 2 a i soff - supply current - disabled no load, v in = 0v -25 -14 -5 a psrr power supply rejection ratio dc, v s = 4.75v to 5.25v 65 74 85 db -ipsr - input current power supply rejection dc, v s = 4.75v to 5.25v -0.5 0.1 0.5 a/v enable (el5160 only) t en enable time 200 ns t dis disable time 800 ns i ihce ce pin input high current ce = v s + 5 10 15 a i ilce ce pin input low current ce = v s --101a v ihce ce input high voltage for power-down v s + - 1 v v ilce ce input low voltage for power-down v s + - 3 v note: 1. standard ntsc test, ac signal amplitude = 286mv p-p , f = 3.58mhz electrical specifications v s + = +5v, v s - = -5v, r f = 750 ? for a v = 1, r f = 400 ? for a v = 2, r l = 150 ? , v enable = v s + - 1v, t a = 25c, unless otherwise specified. parameter description conditions min typ max unit el5160, el5161, el5260, el5261, el5360
5 el5160, el5161, el5260, el5261, el5360
|
